bearing induction remover ACEPOM ZNCX series Electromagnetic heater bushing mill 10 seconds
bearing induction remover ACEPOM ZNCX series Electromagnetic heater bushing mill 10 seconds
- Detail
- Parameters
ZNCX series bearing induction disassembly is widely used in rolling mills, railway departs, ports, docks and other industrial and mining enterprises. A new generation of products for thermal disassembly of bearing inner ring, retaining ring, sealing ring, gear coupling, etc. ZNCX series bearing induction dismantleer applies the principle of electromagnetic induction to generate an induced current in the inner ring of the bearing to make it expand, thus creating a gap at the mating place to achieve the purpose of easy disassembly. Because the induction heating is rapid, uniform, clean, pollution-free, high heating quality, and to ensure that the bearing is not damaged, this advanced disassembly method is gradually replacing baking, oil cooking and other methods.
ZNCX bearing induction installation and removal device Main structure:
The machine is composed of main control cabinet, stainless steel disassembling ring and other parts.
Disassembly use and operation:
1. Connect the control cabinet to the controlled power supply;
2. Connect the control cabinet with the disassembly ring with a wire;
3, close the control switch, the voltmeter should be indicated at this time;
4. Put the disassembly ring on the workpiece;
5, adjust the required heating time, press the start button, heating starts. When the workpiece is heated to the required time, the host will automatically turn off the power or press the stop switch;
6, after the heating is finished, take out the disassembling ring and remove the workpiece;
Note:
1, this series of bearing induction remover must be customized by the user to provide the size of the heating workpiece;
2, take out the workpiece to use heat insulation gloves;
3. The heating parts of the disassembly ring must be removed after the host is powered off.
Installation, use and operation:
1. Connect the control cabinet to the controlled power supply;
2. Connect the control cabinet with the disassembly ring with a wire;
3, close the control switch, the voltmeter should be indicated at this time;
4, put the workpiece into the disassembly ring;
5, adjust the required heating time, press the start button, heating starts. When the workpiece is heated to the required time, the host will automatically turn off the power or press the stop switch;
6. After heating, remove the workpiece and install it on the shaft;
Note:
1, this series of bearing induction remover must be customized by the user to provide the size of the heating workpiece;
2, take out the workpiece to use heat insulation gloves to prevent violence;
3. The heating parts of the disassembly ring must be removed after the host is powered off.
The machine is composed of main control cabinet, stainless steel disassembling ring and other parts.
Disassembly use and operation:
1. Connect the control cabinet to the controlled power supply;
2. Connect the control cabinet with the disassembly ring with a wire;
3, close the control switch, the voltmeter should be indicated at this time;
4. Put the disassembly ring on the workpiece;
5, adjust the required heating time, press the start button, heating starts. When the workpiece is heated to the required time, the host will automatically turn off the power or press the stop switch;
6, after the heating is finished, take out the disassembling ring and remove the workpiece;
Note:
1, this series of bearing induction remover must be customized by the user to provide the size of the heating workpiece;
2, take out the workpiece to use heat insulation gloves;
3. The heating parts of the disassembly ring must be removed after the host is powered off.
Installation, use and operation:
1. Connect the control cabinet to the controlled power supply;
2. Connect the control cabinet with the disassembly ring with a wire;
3, close the control switch, the voltmeter should be indicated at this time;
4, put the workpiece into the disassembly ring;
5, adjust the required heating time, press the start button, heating starts. When the workpiece is heated to the required time, the host will automatically turn off the power or press the stop switch;
6. After heating, remove the workpiece and install it on the shaft;
Note:
1, this series of bearing induction remover must be customized by the user to provide the size of the heating workpiece;
2, take out the workpiece to use heat insulation gloves to prevent violence;
3. The heating parts of the disassembly ring must be removed after the host is powered off.
Origin
China
Brand
ACEPOM
Model
ACEPOM ZNCX series
