Medium induction Bearing heater TIH 100m electromagnetic induction Multi function induction heater
Medium induction Bearing heater TIH 100m electromagnetic induction Multi function induction heater
- Detail
- Parameters
SKF Induction Heater TIH 100M (230V version)
The SKF TIH 100M is a medium sized induction heater and is designed for the hot mounting of bearings. This compact heater is ideal for use on workbenches and can easily be transported to on-site applications with the optional heater trolley TIH T1. The heater is supplied with a swivel yoke and two optional yokes for smaller bearings. The TIH 100M can heat small bearings with a bore diameter of just 20 mm and larger bearings with a maximum weight of 120 kg.
Supplied with a swivel yoke and two smaller yokes, located in an integrated storage compartment
Easy and safe to use with automatic temperature control or time controlled heating
Automatic demagnetization reduces risk of bearing contamination
Suitable for non-bearing applications for workpieces weighing up to 60 kg
Automatic temperature hold function to keep the bearing hot after completion of the heating cycle
| Designation | TIH 100m | |
| SKF m20 performance | 97 kg (213 lb) | |
| Voltage, V/Hz | - TIH 100M/230V | 230V/50-60Hz |
| - TIH 100M/MV | 400-460V/50-60Hz | |
| Bearing: | - Maximum weight | 120 kg (264 lb) |
| - Maximum bore diameter | 20 - 400 mm (0.8 - 15.7 in.) | |
| Temperature control: | - Range * | 0 - 250 °C (32 - 482 °F) |
| - Magnetic probe | Yes, K-type | |
| - Accuracy (electronics) | ± 2 °C (± 3,6 °F) | |
| Time control: | - Range | 0 - 60 minutes |
| - Accuracy | ± 0,01 sec. | |
| Performance example: | - bearing, weight, temperature, time | 23156 CC/W33, 97 kg, 110 °C, 20m |
| Thermometer mode | Yes | |
| Bearing mode | Yes | |
| Power reduction | 2-step; 50 - 100% | |
| Demagnetisation according to SKF norms (automatic) | Yes (<2 A/cm) | |
| Can heat sealed bearings | Yes | |
| Can heat pre - greased bearings | Yes | |
| Error guiding codes | Yes | |
| Thermal overload protection | Yes | |
| Maximum magnetic flux | 1,7 T | |
| Control panel | Key board with LED in remote control | |
| Operating area (w × h) | 155 × 205 mm (6.1 × 8.0 in.) | |
| Coil diameter | 110 mm (4.3 in.) | |
| Dimensions (w × d × h) | 570 × 230 × 350 mm (22.4 × 9.0 × 13.7 in.) | |
| Total weight, including yokes | 42 kg (92 lb) | |
| Maximum power consumption | 3,6 kVA (230V) | |
| 4,0-4,6 kVA (400-460V) | ||
| Number of standard yokes | 3 | |
| Standard yokes | 56 × 56 × 296 mm (2.2 × 2.2 × 11.7 in.), for heating bearings with bore diameter of 80 mm (3.1 in.) and larger | |
| 28 × 28 × 296 mm (1.1 × 1.1 × 11.7 in.), for heating bearings with bore diameter of 40 mm (1.6 in.) and larger | ||
| 14 × 14 × 296 mm (0.6 × 0.6 × 11.7 in.), for heating bearings with bore diameter of 20 mm (0.8 in.) and larger | ||
| Core cross section | 56 × 56 mm (2.2 × 2.2 in.) | |
| Yoke storage | Yes, foldable | |
| Sliding arm | No | |
| Swivel arm | Yes, large yoke only | |
| Cooling fan | No | |
| Housing material | Steel and glass filled polyamide | |
| * Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact SKF for advice. | ||
