Large induction Bearing heater ACEPOM-AHEATER-220
Large induction Bearing heater ACEPOM-AHEATER-220
- Detail
- Parameters
High heating capacity of up to 300 kg bearing
The large induction heater ACEPOM AHEATER220 is a reliable and robust induction heater from therange. It is suitable for heating bearings up to a maximum weight of 300 kg (660 lbs) and solid components up to a maximum weight of 150 kg (330 lbs).
Advanced design of the power electronics including current and overheating control, combined with user friendly features such as sliding arms and remote control are standard to the TIH...m range.
Maximum efficiency is achieved by placing the induction coil outside the heater’s housing, in the centre of the bearing,resulting in shorter heating time and lower energy consumption.
The LED operating display and control panel are integrated in a remote control, which makes the heater easy to use. To suit different operating voltages worldwide, the ACEPOM-AHEATER-220 is available in different voltage variants.
Capable of heating a 220 kg (480 lbs) bearing in just 20 minutes, saving time and energy
Supplied standard with two yokes, allowing bearings with a bore diameter from 60 mm (2.3 in) up to a maximum weight of 300 kg (660 lbs) to be heated
Foldable bearing support arms allow larger diameter bearings to be heated, and reduce the risk of the bearing toppling during heating
2step power setting and smaller yoke facilitates efficient heating of smaller bearings with a lower power consumption
Temperature mode pre-set at 110 °C (230 °F), helps prevent bearing overheating
Automatic demagnetization
TECHNICAL DATA | ||
Designation | ACEPOM-AHEATER-220 | |
m20 performance | 220 kg (480 lbs) | |
Voltage, V/Hz | ACEPOM-AHEATER-220/50-60Hz | |
Bearing: | - Maximum weight | 300 kg (661.4 lb) |
- Maximum bore diameter | 60 - 600 mm (2.3 - 23.6 in.) | |
Temperature control: | - Range * | 0 - 250 °C (32 - 482 °F) |
- Magnetic probe | Yes, K-type | |
- Accuracy (electronics) | ± 2 °C (± 3.6 °F) | |
Time control: | - Range | 0 - 60 minutes |
- Accuracy | ± 0,01 sec. | |
Performance example: | - bearing, weight, temperature, time | 23172 CC/W33, 220 kg, 110 °C, 20m |
Thermometer mode | Yes | |
Bearing mode (pre-set at 110 °C/230 °F) | Yes | |
Power reduction | 2-step; 50 - 100% | |
Demagnetisation according to norms (automatic) | Yes (<2 A/cm) | |
Can heat sealed bearings | Yes | |
Can heat pre - greased bearings | Yes | |
Error guiding codes | Yes | |
Thermal overload protection | Yes | |
Maximum magnetic flux | 1,55 T | |
Control panel | Key board with LED in remote control | |
Operating area (w × h) | 250 × 255 mm (9.8 × 10 in.) | |
Coil diameter | 140 mm (5.5 in.) | |
Dimensions (w × d × h) | 750 × 290 × 440 mm (29.5 × 11.4 × 17.3 in.) | |
Total weight, including yokes | 86 kg (189 lbs) | |
Maximum power consumption | 10,0-11,5 kVA (400-460V) | |
Number of standard yokes | 2 | |
Standard yokes | 70 × 70 × 430 mm (2.8 × 2.8 × 16.9 in.), for heating bearings with bore diameter of 100 mm (3.9 in.) and larger | |
40 × 40 × 430 mm (1.5 × 1.5 × 16.9 in.), for heating bearings with bore diameter of 60 mm (1.6 in.) and larger | ||
Core cross section | 70 × 70 mm (2.8 × 2.8 in.) | |
Yoke storage | Yes | |
Sliding arm | Yes, 70 x 70 x 430 mm (2.8 x 2.8 x 16.9 in.) yoke only | |
Swivel arm | No | |
Cooling fan | No | |
Housing material | Steel and glass fibre filled polyamide | |
* Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact for advice. | ||
